Professional Paulownia Cultivation Technology · Shaanxi, China Contact us: paulownia@vip.126.com🌐 EN ES AR RU DE FR JA KO
chinesepaulownia logo chinesepaulowniaWeinan Research & Promotion Center for High Resistance Paulownia
Home / News / Research

Paulownia Swelling Pressure: Lowest of Seven Woods

November 2026 · Research · Wood Properties

A paper published on 12 November 2026 in Materials puts a number on something furniture makers have long understood by feel: paulownia does not fight its joints. The study, from the Department of Wood Science and Thermal Techniques at Poznan University of Life Sciences in Poland, measured swelling pressure — the force a piece of wood exerts when it wants to swell but is held back — in seven species: sapele, khaya, framiré, tauari, abura, mansonia and plantation-grown paulownia.

Paulownia boards stacked after drying, showing pale sapwood and darker heartwood

Paulownia came last on both axes. Stuck at the bottom of a table that runs from 1.17 to 8.85 megapascals, it is not a marginal difference: the stiffest species pushes roughly seven times harder when restrained. For anyone specifying paulownia into a frame, a floor, a door or an instrument, this is the most useful single property measurement to appear in years.

What swelling pressure actually measures

Wood moves. Everyone in the trade knows that a board widens in humid air and narrows in dry air, mostly across the grain. What is less often quantified is what happens when the board cannot move — when it is screwed flat to an apron, glued into a groove, trapped behind a skirting or laminated to a substrate that does not expand.

Swelling pressure is the stress that builds in that situation. It is the reason a tabletop splits along the grain in February, why a cabinet door panel bows, why a floor buckles at a doorway. The wood is not defective; the detailing gave it nowhere to go, and the accumulated force found the weakest point. In a mixed assembly, the softer wood usually loses — and takes the glue line with it.

The test, and the numbers it produced

The Poznan team took oven-dry specimens of each species, six replicates per species in each anatomical direction, restrained them from swelling, and submerged them. Force was logged from the dry state until it peaked and then stabilised or began to fall. Testing from oven-dry through to full saturation is deliberately harsh: it captures the worst case rather than a service condition, which is what a designer wants for a safety margin.

Maximum tangential pressure across the seven species ran from 1.81 to 7.00 MPa; radial pressure from 1.17 to 8.85 MPa. Sapele was highest in both directions at 7.00 and 8.85 MPa. Paulownia was lowest at 1.81 and 1.17 MPa. The study also found that pressure developed differently over time: paulownia, abura and mansonia climbed to comparatively low maxima quickly, while sapele and khaya built higher pressures slowly. Tauari was the awkward case — fast onset and a high peak.

Density explained a fair share of the variation, with R² of 0.68 tangentially and 0.62 radially. Compressive modulus of elasticity explained some of the tangential result (R² = 0.61) and none of the radial one. Species of similar density still diverged substantially, which is the study's pointed conclusion: density and stiffness alone will not let you predict how hard a wood pushes.

Why a low number is worth money

The practical reading is straightforward. Paulownia generates little restrained stress, so cross-grain assemblies survive better than they have any right to. A paulownia panel in a fixed rebate, a paulownia drawer bottom in a groove that was cut slightly tight, a paulownia substrate under a brittle veneer — these are the details where a high-swelling species fails and paulownia quietly gets away with it. That tolerance is worth real money in a factory where seasonal humidity swings across a 12–18% equilibrium moisture content band are normal and every complaint costs a replacement.

There is a second, less obvious consequence. Because the pressure stays low, clamping and glue-up are gentler on the assembly, and the risk of a starved glue line or a split frame from seasonal movement drops. The paper's density correlation hints at why: a light, low-density wood yields and crushes at the interface before it can transmit much force. That is good news for the joint and mildly bad news for the wood — it means paulownia dents at clamp points and under hard fasteners more readily than a dense species would.

What the number does not tell you

Three cautions, because this is where specifications go wrong.

First, swelling pressure is not swelling. The study says nothing about how far a paulownia board grows between 8% and 16% moisture content, and a low-pressure wood can still move a perfectly ordinary amount. You still have to dry to the destination climate's equilibrium moisture content and still have to leave a movement allowance. Low pressure means the wood is forgiving of a tight detail, not that detailing no longer matters.

Second, submerged specimens are a laboratory worst case. In a humid room the wood never reaches full saturation, so real-world pressures sit well below these figures. Use the comparison between species, not the absolute values, when you are deciding what to put inside a frame.

Third, nothing here improves screw withdrawal or nail holding. Paulownia's low density remains a fastener problem, and it needs to be solved with through-bolts, inserts, glue area or mechanical fixings, not with hope. A wood that will not split your frame can still let your bracket pull out.

The broader lesson is that paulownia is best specified for what it does well — light, stable, quiet in an assembly — rather than as a substitute for a dense hardwood in a joint that was designed around a dense hardwood. The Poznan data simply makes that argument measurable.

Sources & Further reading

Buying paulownia for a panel, frame or soundboard, or growing it for that market? Email paulownia@vip.126.com — tell us the component, the destination climate and the moisture specification, and we will advise on variety, drying target and the detailing that suits the material.

← Back to all news · Paulownia boards: moisture and tolerance specs · Paulownia wood: properties, uses and markets